scaffolding couplers, including connecting steel pipes, flat steels, hardwood wedges and cross buckles, etc. This article will introduce the relevant knowledge of the scaffolding coupler, I hope it will be helpful to everyone.
The installation process of the scaffolding coupler.
The scaffolding coupler products owned by the company.
When setting up an external scaffold, the installation process of this scaffolding coupler is as follows:
When there is no post-pouring concrete at the reinforced column head, the first bolt hole on the flat steel is used to tie the pre-embedded reinforced column head in the reinforced concrete structure of the building floor to play the role of tie, and then the two-way connection at the front end of the steel pipe A hardwood wedge is driven into the slope C, and the hardwood wedge of the scaffolding coupler is pressed against the reinforced concrete structure of the building floor. After pulling and topping, a force couple is formed, making the connecting steel pipes unable to rotate in the left and right directions, and then the cross buckle is used to connect The rear end of the steel pipe is connected with the riser of the outer scaffold, so that while ensuring the lateral stability of the outer scaffold, it also achieves the effect of promoting longitudinal stability. Because the cross buckle of the scaffolding coupler is used to connect the connecting steel pipe with the outer scaffolding riser, the connection at the rear end of the connecting steel pipe can be adjusted. The distance between the outer scaffold and the reinforced concrete structure of the building floor can be different, and the rear end of the connecting steel pipe can be selected differently. Cross buckles are used to connect the outer scaffold standpipe at the connection point, so that the scaffolding coupler has freedom and flexibility in the installation distance. A hardwood wedge is driven into the two-way slope at the front end of the connecting steel pipe. The hardwood wedge of the scaffolding coupler presses against the reinforced concrete structure facade of the building floor. The risers of the scaffolding are connected.
The products provided by Nanjing Tuopeng are high-quality and affordable scaffolding materials. Customization requirements can be met here. Our products are exported to Canada, the United States, Trinidad and Tobago, New Zealand, Thailand, Malaysia, Colombia, the Middle East, Poland and other European countries. We can provide frame scaffolds, scaffolding couplers, ring lock scaffolds, scaffold tubes, cup lock scaffolds and other products. Among them, the scaffolding coupler includes: scaffold drop forged joints and scaffold press joints.
If you are satisfied with our company's scaffolding coupler, you can directly order or consult the scaffolding coupler related issues. We will provide you with the best scaffolding coupler products and services. Looking forward to your visit, I wish you success in your work.
This article covers a scaffolding coupler. Scaffold refers to various supports erected on the construction site for workers to operate and solve vertical and horizontal transportation. Scaffolds are usually made of bamboo, wood, steel or synthetic materials. The existing scaffolds use extended stationary scaffolding coupler in the form of a universal shaft for the purpose of mounting diversity.
1. The necessity of scaffolding coupler
2. The existing scaffolds’ disadvantages
3. The advantage of using scaffolding coupler
Scaffold refers to various supports erected on the construction site for workers to operate and solve vertical and horizontal transportation. Scaffolds are usually made of bamboo, wood, steel or synthetic materials. Scaffolding is also used as a formwork for some projects, and is also widely used in advertising, municipal, transportation, roads and Bridges, mining and other sectors. Scaffold is divided into door type scaffold, bowl buckle type scaffold, common fastener type scaffold according to the way of connection. Common fastener scaffold is connected to the vertical pipe through the plug connected in the horizontal pipe inserted in the wheel buckle connected in the vertical pipe, to achieve the connection between the vertical pipe and the horizontal pipe.
The existing scaffolds use extended stationary scaffolding coupler in the form of a universal shaft for the purpose of mounting diversity. Although this kind of scaffolding coupler is practical, its stability is poor and Angle deflection is easy to occur. However, in some fields such as stage construction and billboard construction where the installation Angle, aesthetics and stability of scaffolding are high, most of the scaffold extension and fixed connectors cannot be met.
Scaffolding coupler is a generic term in the architecture world. It refers to the construction site used in the external wall, internal decoration or high floor where direct construction is impossible. This is mainly for the construction personnel up and down work or external safety net envelope and overhead installation components to put it bluntly is to build shelves.
Scaffolding coupler includes scaffolding and crossbar. The main body of the scaffolding coupler consists of a connecting cylinder and a clamping cylinder. The connecting cylinder is six, and the tail of the six connecting cylinders is a whole. The orientation of each connection barrel is the six axial directions of the space respectively, that is, the front, back, left and right up and down orientation of the connection center of the six connection barrels. The scaffolding coupler ‘s clamping cylinder is a hollow straight cylinder with three circular clips inside. Each clip is provided with a welded second clip, and the cylinder wall of the connecting cylinder is provided with three bolt holes. The second clip is threaded into three bolt holes on the wall of the connecting cylinder. The rear end of the clamping cylinder is closed. A socket is arranged on the pole. The receptacle is a set of cylindrical parts on the riser. The socket is provided with a plug along its circumference. The plug is a convex block with a narrow top and a narrow bottom, a narrow outside and a thin inside. The crossbar is provided with a socket that matches the shape of the plug. The socket is provided with threads. Compared with the existing technology, the scaffolding coupler is simple, plug and play, practical and reliable, convenient for the installation and disassembly of scaffolding, and the scaffold structure is solid.
5' Wide x 6' 6" Tall Walk-Thru Scaffold Frame Set
Frame Leg: 1.625" OD (1-5/8")
Lock Spacing is 27-3/4"
Each Set Includes:
2 - 5'W x 6' 6"T Walk-Thru Scaffold Frames
2 - 7' x 27-3/4"' Tubular Cross Braces
4 - Coupling Pins (1-3/8")
4 - Spring Clips
This Frame has 3-Locks on each Leg (27-3/4" between Locks).
5' x 6'6" walk through frame
7' x 27-3/4"' Tubular Cross Braces
Other components are available
Base jack/ levelling jack
Goosers and guard rails
Tubular side bracket
Iron angle side bracket
Scaffolding is often an essential part of building and home maintenance, and negligence in erecting scaffold can lead to serious accidents. We all know that the mason frame scaffolding is easy to install and disassemble, but is it really safe?
What is the stonemason frame scaffolding?
Is the mason frame scaffolding safe?
How to properly install the mason frame scaffolding?
Construction, installation, maintenance, repair and dismantling of scaffolding
Mason frame scaffolding is a common industry term referring to our popular frame and support scaffolding. All types of contractors, from carpenters and masons to weekend project owners, use the most common scaffolding to make bricks or bricks safer and more efficient. It is easy to install and remove, allowing you to reach the required height quickly.
Masonry frame scaffolding is generally used for masonry. mason frame scaffolding consists of two ladders, two pairs of crossbars and four connecting pins. They are usually used by one or two-story residential contractors, painters, etc., but their modular framework can also be used in large construction projects. Stacked many times. In the masonry frame scaffolding, there are two standard frames, 1.5 m from the first standard. The masonry frame scaffolding is
completely independent of the stone wall.
Masonry frame scaffolding is used to carry heavy objects because the weight on the stone is heavy. Therefore, by placing the standard at a fairly close distance, the stonemason frame scaffolding becomes stronger.
In addition to solid safety, masonry frame scaffolding has other advantages
Frame scaffolding is easy to install and remove, saving time and energy.
Workers can climb the ladder smoothly and safely without the need for additional ladders.
The trapezoidal masonry frame scaffolding is especially suitable for brick structures, exterior wall paints or plastering works. It is easy to operate and can be moved with the casters.
Choose the security foundation to build and set up the scaffolding. Obtain a mud plate or bottom plate to secure the scaffolding to make the foundation more stable. One of the main problems here is the basis for the level and safety of scaffolding. If you are on an uneven ground, I need to dig to make dirt at any high corner. In addition, use the adjustment screws on the scaffolding to level the structure. If the surface is on a sharp slope, get a leg stretch.
Select the casters. If you plan to move the scaffolding to various locations, include casters in the scaffold setup. Remember to lock the casters when you put it in place.
Assemble the scaffolding frame. Arrange the end of the scaffold. Lift an end piece and connect the upper beam. When you lift the second end piece and attach its upper beam, the distal end of the support should support the end piece. Secure the ends of the cross braces to the bottom of the opposite end frame.
Make sure the scaffolding is stable. Move the scaffold to the desired location and make sure it is level and strong.
Place the board. Lift the plank through the scaffolding bar and seat it. Hardware should be included to hold the board in place.
Enter the scaffold safely. If using a ladder to enter the scaffolding, use scaffold designed for the scaffolding. Staircase ladders can be used to enter the scaffold, but must have handrails and pedals. One problem with access points is to make the operation safe and prevent the scaffold from tipping over.
Connect the guardrail. Due to the height of the equipment and the risk of falling, it is highly recommended that all scaffolds use guardrails. Also consider the use of cable ties and other fall arresters.
Check the scaffold for safety. Thoroughly check the scaffold settings to make sure all parts are safe. Re-examine the scaffolding system and return to the site each time you leave the site to ensure it is still safe.
It is the responsibility of the occupants of the workplace to build, erect or install scaffold on or under construction.
Partially constructed, erected, installed or removed scaffolding or parts thereof shall not be used unless safe.
If any scaffold is unsafe to use, an obvious warning notice or sign shall be issued in a form that is easily understood by all, indicating that the scaffold or part thereof is not to be used and that it must be placed anywhere, depending on the circumstances, the scaffold or parts may Being approached for use.
Each scaffold shall be properly maintained and each part shall be fixed, fixed or placed to prevent any accidental displacement, to the extent reasonably practicable.
Any damaged or weakened scaffold and any components or components thereof shall be repaired as soon as reasonably practicable.
No one shall be allowed to enter a damaged or damaged scaffold except for the scaffolding erector who is repairing the scaffold.
All reasonable and practicable measures shall be taken to ensure the safety of the person performing the repairs described.
If the attachment of the scaffold to the permanent structure must be removed, the appropriate removal of the scaffolding portion of the fitting should be removed unless appropriate measures are taken to ensure the stability of the scaffold.
The mason frame scaffolding is very sturdy at the same time, so you can make sure it is safe, but more importantly, you have mastered the proper installation and use of scaffold. If you need a well-tested, sturdy, high quality mason frame scaffolding, Nanjing Tuopeng Construction Technology can provide you with the perfect product.
System scaffolding is a new type of in-line steel scaffolding with self-locking function. This article will introduce the relevant knowledge of system scaffolding, and I hope it will be helpful to everyone.
Acceptance requirements for system scaffolding.
The company has system scaffolding products.
System scaffolding is a working platform erected to ensure the smooth progress of each construction process. Separate out scaffolding and inner scaffolding according to the erection position; divide wooden scaffolding, bamboo scaffolding, steel pipe scaffolding according to materials; separate pole scaffolding, bridge scaffolding, portal scaffolding, suspended scaffolding, hanging scaffolding, and picking type according to the structure form Scaffolding, climbing scaffolding.
After the scaffolding of the system is set up and assembled, it should be inspected and checked and confirmed to be qualified before operation can be carried out. The foreman in charge, the shelf team leader and the full-time safety technicians in the water section shall organize the acceptance and fill in the acceptance form together.
1. The basic treatment, practice and embedding depth of the system scaffold must be correct and reliable.
2. The arrangement of the system scaffolding, the spacing of the vertical poles, and the large and small cross-bars should meet the requirements.
3. The erection and assembly of the system scaffold, including the selection of tool racks and lifting points, should meet the requirements.
4. The wall point of the system scaffold or the fixed part of the structure should be safe and reliable; the scissor brace and diagonal brace should meet the requirements.
5. The safety protection and safety devices of the system scaffolding must be effective; the tightening degree of the fasteners and lashings must meet the requirements.
6. The installation of hoisting tools, wire ropes, and booms of the system scaffolding should be safe and reliable, and the laying of scaffolding boards should comply with regulations.
With the emergence of a large number of modern large-scale construction systems in China, fastener-type steel pipe scaffolding can no longer meet the needs of construction development, and it is urgent to develop and promote the application of new scaffolding. Practice has proved that the use of system scaffolding is not only safe and reliable in construction, and fast in assembly and disassembly, but also the steel consumption of the system can be reduced by 33%.
Nanjing Tuopu Construction Technology Co., Ltd. is a professional system scaffolding manufacturer and the safest system scaffolding material exporter in China, with competitive prices. Customization requirements can be met here. Our products are exported to Canada, the United States, Trinidad and Tobago, New Zealand, Thailand, Malaysia, Colombia, the Middle East, Poland and other European countries. Whether you are a distributor, contractor or factory, you can always find what you need from us.
We can provide frame scaffolds, scaffold connectors, layered scaffolds, scaffold tubes, cup lock scaffolds, scaffold clips, system scaffolding and other products.
If you are satisfied with our company's system scaffolding, you can directly order or consult related issues of the system scaffolding. We will provide you with the best system scaffolding products and services. Looking forward to your visit, I wish you success in your work.
scaffolding frame ensures the smooth progress of the construction process. This article will introduce the relevant knowledge of scaffolding frame, I hope it will be helpful to everyone.
Features of scaffolding frame.
scaffolding frame products owned by the company.
Different types of construction use scaffolding frame and formwork supports for different purposes. At present, most of the bridge support frames use bowl buckle scaffolding frame, and some use portal scaffolding frame. Most of the main structure uses fastener scaffolding frame, the vertical distance of the scaffolding frame pole is 1.2~1.8m; the horizontal distance is 0.9~1.5m.
Fastener type steel pipe scaffold
1) Larger bearing capacity. When the geometric dimensions and structure of the scaffold meet the relevant requirements of the code, under normal circumstances, the bearing capacity of the single-tube column of the scaffold can reach 15kN～35kN (1.5tf～3.5tf, design value).
2) Convenient assembly and disassembly, flexible installation. It is suitable for scaffolding frame for buildings and structures of various planes and elevations.
3) More economical. The processing is simple and the one-time investment cost is low; if the scaffolding frame geometry is carefully designed and attention is paid to increasing the utilization rate of the steel pipe turnover, the material consumption can also achieve better economic effects. The amount of steel used in the construction of the fastener steel pipe frame is about 15 kilograms per square meter.
Portal steel scaffolding frame
1) Standardization of portal steel scaffolding frame.
2) The structure is reasonable, the bearing performance is good, the strength of steel is fully utilized, and the bearing capacity is high.
3) Easy assembly and disassembly during construction, high erection efficiency, safe and reliable, economical and applicable.
Folding bowl buckle steel pipe scaffold
1) Multi-function: According to specific construction requirements, it can form single and double-row scaffolds with different frame sizes, shapes and load-bearing capacities, support frames, support columns, material lifting frames, climbing scaffolds, cantilever frames and other constructions with multiple functions equipment.
2) High efficiency: The longest length of commonly used rods is 3130mm, and the weight is 17.07kg. Workers can complete the work with a hammer to avoid the inconvenience caused by bolt operation.
3) Strong versatility: The main components are all fastener steel scaffold steel pipes, which can be connected with the steel pipes by fasteners.
Nanjing Tuopeng Construction Technology Co., Ltd. is a professional scaffolding frame manufacturer and exporter of all kinds of safest scaffolding frame materials in China, with competitive prices. Customization requirements can be met here. Our products are exported to Canada, the United States, Trinidad and Tobago, New Zealand, Thailand, Malaysia, Colombia, the Middle East, Poland and other European countries. Whether you are a distributor, contractor or factory, you can always find what you need from us.
We can provide frame scaffolds, scaffold connectors, ring lock scaffolds, scaffold tubes, cup lock scaffolds, scaffold clips and other products.
If you are satisfied with our company's scaffolding frame, you can directly order or consult the scaffolding frame related issues. We will provide you with the best scaffolding frame products and services. Looking forward to your visit, I wish you success in your work.